0

Your Cart is Empty

ELC.00.30000

Denali PowerHub2 Fuse Block, Master Ground Block and Wiring Harness

#1 Best Seller
in Denali
1
1 item left

Denali's PowerHub 2 Fuse Block Accessory Hub is by far the best way to cleanly wire all of your accessories to your bike. This eliminates the mess of wires from multiple add on's to your battery causing your bike to be a nightmare when servicing. The PowerHub2 allows you to centrally locate all of your accessories power and ground leads into one spot on the bike in a very clean and professional fashion. If you intend on running more than a set of heated grips for example then you should consider the purchase of the PowerHub. This is one of the those purchases that should be considered before installing anything. It will make your life much easier in the end.

The PowerHub2 Power Distribution Module allows you to safely connect up to 6 electronic devices to your motorcycle in a clean, professional manner. It is CAN-Bus compatible and includes six 15-amp rated and fused outputs, six ground posts, and a plug-and-play wiring harness for direct battery hookup. Each of the six outputs can be individually set as "always on" or "switched" on/off with the ignition of the motorcycle. Instead of attaching multiple ring terminals to your battery, use a PowerHub2!

The CAN-bus safe Denali PowerHub2 has been designed to allow simple and easy installation of electrical components. Each unit has six individually fused outputs. These are not your ordinary outputs. Simply plug the fuse in to the left or the right on the circuit board to make the accessory live all of the time or switched on/off with the bike's ignition.

The entire unit is rated for 30 Amps (360 watts). Each of the six circuits can handleup to 15A (180W) each - without exceeding a total sum of 30 Amps simultaneously.

Features:
  • Replaceable 30 amp Tyco/Bosch micro relay
  • Water-resistant
  • Compact
  • Durable
  • Choice between switched and constant power

SPECIFICATIONS

  • Dimensions: L 3" x W 4" x H 1"
  • 6 circuits can handle up to 15A (180W) each
  • CANbus-compatible
  • 60 inch long 10 gauge wiring harness with Posi-lock connector

FITMENT

  • This is a universal fit part; it may or may not fit without modification.

PROPOSITION 65

⚠️WARNING

This product can expose you to chemicals known to the State of California known to cause Cancer or birth defects and reproductive harm. For more information go to: https://oehha.ca.gov/proposition-65

Customer Reviews

Based on 1 reviews
5 ★
0% 
0
4 ★
0% 
0
3 ★
0% 
0
2 ★
100% 
1
1 ★
0% 
0
Write a Review
  • Reviews

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

    JH
    02/26/2019
    James Hamilton

    Great idea but........Pros & Cons

    The units concept of a central wiring hub for all my ADV bike accessories is a great idea....however this unit has several shortcomings and left me disappointed: 1. It is so small it is impossible to utilize all six circuits and still put the lid on the unit (maybe if you are using 20 gauge wire size or smaller for all six circuits it might fit but I doubt it). The wire entrance hole into the enclosure is too small and the terminal strips are tiny and suitable for very small wire sizes only. 2. The fuse terminals where the fuses plug in are extremely tight and the circuit board is not attached to the enclosure.....so when you try to remove a fuse the entire circuit board pulls out of the enclosure. 3. The elastic bands that secure the lid in place are cheesy......this unit should come with an o-ring or gasket sealed lid that is screwed down (especially at this price) 4. Price is way too high. On the Pro side, it does work as advertised, at least on day one. I only hope those tiny terminal blocks hold my wires securely after a few thousand miles of off road adventures.

    be the first to know